Obviously, in most cases, you won’t want to replace the entire floor due to one or two broken tiles. Here is how to remove and replace the broken tiles easily.
Materials:
- Replacement tile
- Tile adhesive
- Grout
- Water
- Grout Scraper
- Hammer
- Pry bar
- Safety glasses
- Trowel
- Grout float
- Sponge
- Small bucket
- Filling knife
Working around the tile joints (seams), scratch out the grout using the grout scraper. You’ll be getting a pretty fine mess going, but you need to get as much of the grout out as possible. This will separate the broken tile(s) from the ones that are not broken and will make it easier to get a pry bar under the edges if necessary later on.
2. Break/Loosen the Tile
With the hammer, hit the tile a couple of times to loosen it from the surface it is adhered to. Depending on the size of the tile, you will probably have to remove it in chunks. Once you’ve broken it up, use the other side of the hammer or the pry bar to lift up the tile pieces.
With the hammer, hit the tile a couple of times to loosen it from the surface it is adhered to. Depending on the size of the tile, you will probably have to remove it in chunks. Once you’ve broken it up, use the other side of the hammer or the pry bar to lift up the tile pieces.
3. Scrape Adhesive
Once you’ve gotten as much of the tile as possible removed, you need to get rid of the old adhesive. Use a scraper, filling knife or even putty knife to scrape it all off.
Once you’ve gotten as much of the tile as possible removed, you need to get rid of the old adhesive. Use a scraper, filling knife or even putty knife to scrape it all off.
4. Clean the surface
To be sure your new tile properly adheres; you will need to at least dust off the surface. At best, try to clean the surface with a damp cloth and some mild soap. Wait until it is completely dry before moving to the next step. Do not use a wet cloth! Damp will pick up the dust; wet will get water under the adjacent tiles and cause a lot of issues later on.
To be sure your new tile properly adheres; you will need to at least dust off the surface. At best, try to clean the surface with a damp cloth and some mild soap. Wait until it is completely dry before moving to the next step. Do not use a wet cloth! Damp will pick up the dust; wet will get water under the adjacent tiles and cause a lot of issues later on.
5. Add New Adhesive
Use the trowel to apply the adhesive back onto the surface (just as the old stuff was.) The layer should be only about ¼ inch.
Use the trowel to apply the adhesive back onto the surface (just as the old stuff was.) The layer should be only about ¼ inch.
6. Set the Tile
Now place the new tile on top of the adhesive and press firmly in the middle, corners, and along the sides. Press many times and even wiggle the tile a little bit to be sure it is set firmly.
Now place the new tile on top of the adhesive and press firmly in the middle, corners, and along the sides. Press many times and even wiggle the tile a little bit to be sure it is set firmly.
7. Re-grout
Now you can mix up your grout into the same paste consistency as the adhesive and use your grout float to smear it along the sides of the tile. Be sure the grout is getting into all of the seams around the tile – don’t leave gaps; fill up each seam completely!
8. Clean up
Finally, you can use your sponge and bucket of water to clean all of the excess grout off the surface of the tiles. The sponge should be damp enough to pick up excess grout, but NOT soaking wet enough to alter the consistency of the grout in the joint.
Finally, you can use your sponge and bucket of water to clean all of the excess grout off the surface of the tiles. The sponge should be damp enough to pick up excess grout, but NOT soaking wet enough to alter the consistency of the grout in the joint.
Source: www.PlumbTile.com
