Tips for Removing Ceramic Tile

 Success at removing ceramic tiles from floors depends on the material the tile was fastened to at installation. In a very old house, the tiles might have been glued directly to a cement subfloor, making removal very difficult. In a newer property (built within the last 40 years), the ceramic tiles were probably fastened to a lightweight cement backer board, nailed to the timber subfloor. Follow these steps for effective removal of ceramic tiles attached to cement board.

What You'll Need:

• 75mm (3-inch) stiff-bladed scraper or filling knife

• Small flat-headed hammer

• Flat garden spade

• Steel crowbar

• Portable angle grinder

• Wet/dry vacuum cleaner

• Wraparound safety goggles

• Heavy leather gloves

• Long-sleeved shirt or jacket

• Half-face dust mask

Step 1: Start at the Edge of the Floor

Prepare to remove tiles from a floor edge that adjoins carpet, vinyl tiles, or other surfaces. Place the scraper under the edge of a tile, and tap it with the small hammer to lift off a tile. Depending on the strength of the tile adhesive, the cement board may come free along with the tiles.

Step 2: Remove the Tile Grout

Pry between the tiles with the scraper to pulverise the grout, so you can more easily pop the tile from the backing board. If the grout is very hard, use the angle grinder to grind out the grout and release the tile more easily.

Step 3: Continue to Remove Single Tiles

Once you have removed the tile grout and a few tiles, slip the scraper under each tile with the handle as close to the floor as possible. Tap the knife handle sharply with the hammer. The tile may break up or lift off all in one piece. Continue to remove tiles until a section of cement board about 20 cm by 15 cm is exposed. Avoid striking ceramic or porcelain tiles with the hammer, as they will shear into razor-sharp flaked pieces.

Step 4: Remove the Cement Board with Tiles Attached

Once you have cleared tiles off an area of cement board, break it up with the hammer so you can see the floor joists. Insert the flat garden spade under the cement board and use it as a lever to remove larger areas of the board with the tiles attached. Stop from time to time and vacuum the area with a wet/dry vacuum cleaner to avoid inhaling cement and tile dust. Move the spade to the left or right side of the floor joist as you encounter the nails used to attach the cement board. The bigger the gap you can create between the cement board and the floor joists, the larger the area of tile you can remove at once.  

Step 5: Remove the Nails from the Cement Board

Use a claw hammer or a steel crowbar with a nail slot to pull the nails out of the cement board. You can then remove these fragments from the floor joists and dispose of them.  

Step 6: If the Cement Board was Screwed Down

Use a power drill with a screwdriver bit to back the screws out of the cement board pieces, then remove and discard them. Vacuum the room thoroughly to remove dust from all surfaces.

Source: www.DoItYourself.com

Removing Ceramic Tile

 Depending on where they are and how they're installed, removing ceramic tiles can be either a nightmare or a relatively simple job requiring little effort. Stripping all the ceramic tiles from a wall or floor, rather than just trying to remove one or a small number, will also be easier simply because you're not worrying about damaging the surrounding tiles. Here are a number of different situations in which you’ll be removing ceramic tile and some ideas on how to do it right.

What You'll Need:

• Putty knife
• Hammer
• Chisel
• Flat-blade shovel
• Safety glasses
• Gloves
• Dust mask

Ceramic Wall Tiles on Cement Board or Gyproc

This is by far the easiest situation. If you want to protect the underlying wall, take a three-inch, stiff putty knife and hold it at a very low angle relative to the wall. Starting at the edge of the wall, place the blade against the mastic and give the handle a solid tap with a hammer. In most cases the knife will slide under the tile and by simply lifting the handle up, the tile will pop off the wall.

Removing a single tile from a wall can be trickier. In this case, your first step is to remove the grout surrounding the tile using a rotary tool, a thin chisel, or a grout removing tool. Once you've taken care of the grout, use your stiff putty knife again, tapping the end to slide it under the tile.

Removing Tiles on Concrete Board

Removing floor tiles laid on cement board is more work than wall tiles but the methodology is similar. Choose an edge, where flooring and the wall come together, and start by removing any edgings or moldings. Now, you may be able to remove a starter tile using your putty knife, but more likely, you will need to remove the grout around a few tiles first.

Once you get a few starter tiles off the floor, break up the underlying cement board by banging on it with your hammer and discard it. Now you've created a small opening where you can slide a flat-bladed shovel under both the cement board and the ceramic tiles. Lifting up the shovel from underneath will break the cement board and the grout holding the tile so you can remove it. Repeat the process, sliding the shovel under the cement board then lifting and you can get rid of the floor in chunks.

Old Ceramic Tiles Laid Directly onto a Cement Base

This is by far the most difficult situation to deal with and thankfully this installation technique isn't used anymore. There are lots of old homes with ceramic tiles installed right onto a cement base. Once the mortar has cured, the concrete base and the floor tiles are in reality a single piece. There are only a few ways to remove ceramic tiles in this situation. One solution is to break up the tiles with a sledge hammer. However, it's a back-breaking, labor intensive project, and you risk damaging the base if you’re not careful.

The easier solution to this problem is to use a chisel and a hammer. You will want to start at a broken tile, if you have one, or in an area with loose grout so you can get the chisel under the tile. As you get the chisel tip underneath, tap the end of the tool with your hammer to work it further in. These tools will also work to chip away at the old thinset mortar adhered to the floor, which can’t be removed with a sledgehammer. It will be a time-consuming job, but one that will get you a good, clean subfloor to proceed from.

A Safety Reminder

No matter whether you're removing a whole floor or wall of tiles or just a single tile, remember you need to wear wrap-around eye protection, good quality work gloves, and a dust mask. Obviously, it's also a good idea to place protective covering on the floors and walls around where you're working.

Source: www.DoItYourself.com

Cleaning Up a Grubby Shower Cubicle in Bishopton

This shower cubicle was installed in the main bathroom of a house in Bishopton where the grout had become quite grubby and the Ceramic tiles were looking quite dull. The owner was thinking about re-tiling the bathroom and thought they would give us a call first to see if we could refresh the look without the expense. Cleaning Ceramic Tile and Grout We started by spraying the tiles with Tile Doctor Oxy-Pro which is a strong high-alkaline cleaner especially formulated and packaged for cleaning Read more...

To read more on this topic click here

Deep Cleaning a Dirty Shower Cubicle in Middlesbrough

Here's a fairly straightforward job I completed at a house in Middlesbrough which if you haven't come across it before is a large industrial town situated on the south bank of the River Tees famous for its football club. My client was keen to have the Ceramic tiled shower cubicle in her bathroom refreshed, paying particular attention the areas where the tiles and grout had been stained by the chemicals in shampoos and soaps. There was also signs of mould build-up that needed to be addressed. Read more...

Ceramic Tiled Bath and Shower Tiles Refreshed in Hale Village

We commonly encounter customers who are struggling to keep their Ceramic tiled shower cubicles clean. Since most people use their showers every day, the tiles and grout inevitably come into contact with shampoos and soaps that can cause staining, discolouration and mould. In fact, it's not uncommon for property owners to completely give up on trying to clean the tiles, especially as many everyday cleaners are ineffectual, and this allows the situation to worsen over time. This customer, who Read more...

Cleaning Ceramic Tile and Grout in a Shower Cubicle

As you can see from the photographs below the ceramic tiles and grout in this Shower Cubicle in East Sussex were in need of a deep clean. Ceramic tiles are very easy to clean however the grout was very discoloured and so we decided to apply a grout colourant. Cleaning Shower Tile and Grout To clean up the ceramic tiles and grout we sprayed on Tile Doctor Oxy-Pro which is a specialist Shower Tile and Grout Cleaner, the spray allows the cleaning agent to mix with air making it lighter and Read more...

Bathroom Tile and Grout Facelift in Didsbury

This Ceramic tiled bath with shower was installed at house in Didsbury, this customer wanted to give the bathroom a facelift and not usually it was the grout rather than the ceramic tile that had discoloured, the silicone also needed to be replaced due to the mould build-up and if you get mould on silicone it's impossible to remove and can only be replaced. Unfortunately mould build-up in bathrooms is quite common in the UK due to our damp climate and modern insulated homes that restrict air flow. If you're having this problem yourself consider installing a more powerful extractor fan or simply leaving the door to the bathroom open more often. Cleaning Tile and Grout The Ceramic tiles and grout were treated using a strong 2:1 dilution of Tile Doctor Pro-Clean which is a highly recommended Tile and Grout cleaning product; being alkaline it's safe to use on all sorts of tile and stone surfaces. For vertical tiled surfaces I recommend the mixture is decanted into a bottle with a Read more...

Restaurant Tile Cleaning

The Ceramic floor tiles shown below were installed in a Luton high street restaurant, as you can see they were far from clean, deeply stained and even the grout had gone black. Cleaning Ceramic Floor Tiles Given the amount of dirt on the tile and grout we decided to apply a very strong Read more...

Tackling stained ceramic tiles

This was a rather unusual request we were asked to look at in the Oxfordshire village of Long Hanborough; they had recently laid a new Tarmac drive and unfortunately it had been walked into the Ceramic tiled kitchen floor leaving a lot of dark staining. After failing to clean the tiles with Read more...

To read more on this topic click here

Ceramic Tiled Bathroom Refreshed in Kettering

This was a straight forward request to rejuvenate the ceramic tile and grout around the bath at a house in the town Kettering. The glazed ceramic tiles where in good condition but the grout and seal around the bath had become quite grubby and stained with dyes from shampoos, soaps and had gone dark in some areas where mould had started to get a foothold. Cleaning Ceramic Tile and Grout We started by spraying the tiles with Tile Doctor Oxy-Pro which is a strong high-alkaline cleaner Read more...

Effective Tile and Grout Cleaning

This Ceramic tiled family bathroom with shower was installed at house in Leighton Buzzard and was in need of rejuvenation. You can see from the photograph below that the tiles were in reasonable condition but the grout had become ingrained with dirt which is not unknown as the top layer of grout Read more...

Deep Cleaning Dirty Ceramic Tiled Floors

The photograph below was taken in the kitchen of a residence in Bedford where the new owner wanted the Ceramic floor tiles deep cleaned before they moved in; you can see for yourself how dirty they had become. Cleaning Ceramic Floor Tiles To get the clean Ceramic tiles clean I applied a medium Read more...

Cleaning Ceramic Shower Tiles

This shower cubicle was installed in the main bathroom of a house in Bishopton where the grout had become quite grubby and the Ceramic tiles were looking quite dull. The owner was thinking about re-tiling the bathroom and thought they would give us a call first to see if we could refresh the Read more...

Cleaning Ceramic Tiles at Luton High street restaurant

The Ceramic floor tiles shown below were installed in a Luton high street restaurant, as you can see they were far from clean, deeply stained and even the grout had gone black. Cleaning Ceramic Floor Tiles Given the amount of dirt on the tile and grout we decided to apply a very strong combination of Tile Doctor Remove and Go mixed 50/50 with NanoTech Ultra Clean which results in the creation of a heavy duty stripper/cleaner containing nano sized abrasive particles that can penetrate deep Read more...

Cleaning Ceramic Tiles at Luton High street restaurant

The Ceramic floor tiles shown below were installed in a Luton high street restaurant, as you can see they were far from clean, deeply stained and even the grout had gone black. Cleaning Ceramic Floor Tiles Given the amount of dirt on the tile and grout we decided to apply a very strong combination of Tile Doctor Remove and Go mixed 50/50 with NanoTech Ultra Clean which results in the creation of a heavy duty stripper/cleaner containing nano sized abrasive particles that can penetrate deep Read more...

Maintaining Textured Ceramic Tiles

These grubby looking Textured Ceramic Tiles were in a bathroom of a house in the old village of Narborough near Leicester. As you can see from the picture below they were overdue for a deep clean and the customer has been struggling to do that. On inspection it was clear that the textured Read more...

Shower Cubicle Tile and Grout Refresh in Hale

This Ceramic Tiled shower cubicle in a house in Hale was overdue a deep clean, the Ceramic Tiles were in reasonable condition but the grout lines had discoloured and become stained from the dyes in shampoo's and soaps and the silicone needed to be replaced. Cleaning Shower Tile and Grout To clean the grout I decanted a strong 2:1 dilution of Tile Doctor Pro-Clean into a spray bottle and sprayed the solution on the tile and grout working in small sections. I think I've mentioned this before but in case you were wondering mixing the cleaner with air makes it lighter and allows it to stick onto vertical surfaces better. The solution was then worked in using a stiff scrubbing brush by hand before being rinsed off with water; this process was repeated until all the tile and grout was clean and then left to dry. If you're doing this work yourself then you should know that Tile Doctor produces a product that comes with a spray attachment called Oxy Pro that is ready to use and can save Read more...

Dealing with Mould in Ceramic Shower Cubicle

The photographs below are from the bathroom of a house in the Moston area of Manchester which is primarily residential and only 3 miles away from the city centre. My customer had been primarily concerned with the removal of unsightly mould but was also keen to have the grout in the ceramic tiled Read more...

Removing Mould from a Ceramic Tiled Shower Cubicle in Moston

The photographs below are from the bathroom of a house in the Moston area of Manchester which is primarily residential and only 3 miles away from the city centre. My customer had been primarily concerned with the removal of unsightly mould but was also keen to have the grout in the ceramic tiled shower cubicle given a good deep clean. Cleaning a Ceramic Tiled Shower Cubicle To clean the Shower Cubicle, I used a strong dilution of Tile Doctor Pro Clean which is a strong alkaline cleaner that works really well on grout. The Pro-Clean solution was decanted into a spray bottle and then sprayed onto the grout lines and left it to dwell. The air in the solution makes it lighter and easier for it to stick to vertical surfaces. After a few minutes the Pro-Clean was scrubbed in using a stiff grout brush. The tiles were then rinsed with water to remove the soiled solution from the tiles and the process repeated where required. Although cleaning process was a success there were still a few Read more...

Ceramic Tiled Bathroom Cleaned and Sealed in Leighton Buzzard

This Ceramic tiled family bathroom with shower was installed at house in Leighton Buzzard and was in need of rejuvenation. You can see from the photograph below that the tiles were in reasonable condition but the grout had become ingrained with dirt which is not unknown as the top layer of grout is porous and will discolour over time if not protected. Cleaning Ceramic Tile and Grout The Ceramic tiles and grout were treated using a strong 2:1 dilution of Tile Doctor Pro-Clean mixed 50/50 Read more...