Getting the Best From Multi-Coloured Slate in Yorkshire

The owner of this house in Silkstone, which is a village situated in the foothills of the Pennines a few miles West of Barnsley, had inherited this Kitchen Slate floor from the previous owner of the house and in the years, they'd lived at the house they hadn't done anything with the floor. Slate tiles are beautiful but like any natural stone you really need to maintain the sealer if you want them to stay that way, once the sealer wears off dirt can penetrate the pores of the stone resulting in a floor that always looks dull and dirty.


In this case of this Slate floor the sealer had worn off many years prior and a thick layer of grime had built up on top of what was once an amazing looking floor. Stone floors never come with a care guide and the process of degradation happens so slowly, so you can understand how this could happen over time.

Cleaning Dirty Slate Kitchen Tiles

Before starting I protected the wooden kitchen units from splashing using plastic sheeting. Next step was to soak the tiles in a strong dilution of Tile Doctor Remove and Go and Pro-Clean combined into a strong cleaning and stripping cocktail. The solution was left to dwell for ten minutes before being scrubbed in using a black scrubbing pad fitted to a rotary floor machine running at slow speed to break through the grime and the sealers and oils that the previous owner had used on the slate. The pad is good at scrubbing the tiles but struggles to get into the grout so after the tiles were scrubbed I followed by running a stiff brush along the grout lines to give them a thorough clean. The soiled cleaning solution was rinsed off the tiles with water and then extracted off the floor using a wet vacuum. With the floor clear it was inspected, and problem areas re-treated using the same process. Once I was satisfied that the Slate and the Grout was clean and clear of old sealers I gave the whole floor a final rinse to remove any trace of cleaning products and then dried as much as possible using the wet vacuum. The floor was then left to dry out fully overnight.

Sealing Kitchen Slate Tiles

Returning to the property the next day, I ran some quick damp tests to check for any excess moisture that might have prevented me from sealing the floor. We will always do this as excess moisture can affect the sealer curing. Our client had previously decided that they liked the look of our High Shine Sealer due to how it brings the stunning colours of the Slate out. High Shine Sealer is a specially formulated water-based blend of acrylic polymers that provides both a stain resistant surface seal and a durable high-sheen finish. Four coats of sealer were applied and when the customer arrived home later that day they were totally blown away by the floor and how amazing it looked.




Source: Slate Tile Cleaning and Restoration Service in Yorkshire

Renovating Dull Encaustic Hallway Tiles in Hertfordshire

I had an enquiry from a client in the London commuter town of Berkhamsted who had a beautiful Encaustic tiled floor in their hallway which was in need of cleaning. Encaustic tiles are made from layers of cement that are hydraulically compressed to make a very hardwearing surface that can then be decorated. The result is an easy to clean hardwearing surface that is ideal for high traffic areas such as hallways.


Encaustic tiles however are micro-porous so do need to be sealed to prevent dirt from becoming ingrained in the tiny holes. The tiles at this property in Berkhamsted had been sealed at some point in the past but over the years the sealer had worn down lettering dirt enter the pores making it difficult to clean effectively. The floor now required a deep clean and seal to bring back the life into this artistic floor pattern.

Encaustic Tiled Floor Cleaning

We first removed what was left of the old sealer and ground in dirt using a coarse 400 grit Red burnishing pad attached to a rotary floor buffer. The burnishing pads we use are encrusted with industrial diamond and are applied using water for lubrication, once the pad has been run over all the tiles the floor is rinsed with more water which is then extracted with a wet vacuum to remove the slurry that is generated. The coarse pad was the followed by a medium 800 grit burnishing pad which is the first step in restoring the appearance of the tiles and is applied and rinsed off using the same process as the 400 grit. The 800 grit pads is followed by the 1500 grit pad which is the second step In restoring the appearance of the tile. Again, the pad is applied with water to lubricate and the floor given a good rinse afterwards. The next step was to get the grout clean which was done by applying Tile Doctor Pro-Clean which was left for ten minutes before being scrubbed in by hand with a narrow stiff brush. The floor was then given yet another rinse and then dried with the wet vacuum to remove the dirt that was generated from the grout. The last step in the cleaning process was to run over the floor with a very fine 3000 grit pad, this last pad is the final step in restoring the appearance of the tile and is applied dry with only a little water that is sprayed on using a technique we like to call spray burnishing.

Encaustic Tiled Floor Sealing

Once the floor was dry it was sealed using two coats of Tile Doctor Colour Grow which is an impregnating sealer that seeps into the pores of the tile protecting it from within. This sealer has the added advantage of enhancing the existing colours in the tile improving its overall appearance. The overall process worked incredibly well and made a huge difference to the floor as you can see in the final photograph.


To keep Encaustic floor tiles in first class condition I recommend the use of the Tile Doctor Neutral Tile cleaner which being pH neutral does not reduce the life of the sealer and is ideal for the cleaning of all types of sealed floors. The product comes in a concentrated form, so I recommend it’s used in a mild 1-30 dilution spray applied and wiped over with a microfibre flat mop, then buffed dry.


Source: Encaustic Tile Cleaning and Sealing Service in Hertfordshire

Cottage Floor Renovation at National Trust property in Cheshire

Quarry Bank Mill is an old textile mill just outside of Wilmslow in East Cheshire that dates back to the Industrial Revolution when it was used to produce cotton. The mill is now under the care of the National Trust who recently put together a £9.4 million project, supported by the Heritage Lottery Fund the further restoration of the mill and its gardens.

The 18th century mill is now a popular attraction and I was recently asked to clean and seal the Sandstone flooring in the Kitchen of the head gardeners cottage. The cottage is actually located in the formal gardens which were recently visited by HRH Price of Wales.


The Sandstone Kitchen floor was in good physical condition so unlikely to be the original however like any stone floor in constant use the sealer was wearing off and dirt was becoming ingrained in the pores of the stone detracting from its overall appearance.

Cleaning Dirty and Dull Sandstone Flagstones

Our first job was to protect the wooden kitchen units and other woodwork with tape. Next I set about cleaning the Sandstone and stripping any reaming sealer off in the process. To do this I applied a strong dilution of Tile Doctor Remove and Go, which is multi-purpose stripper and cleaner. The product strips away any old sealer on the tiles and draws out ingrained dirt, stains and heavy grease build-up.

I applied the product and left it to soak for roughly fifteen to twenty minutes to allow time to break down the old sealer and penetrate the pores of the stone to reach any embedded dirt. Next, I scrubbed the floor using a specialised buffing machine fitted with a black scrubbing pad swelled with water to get the stone clean. The resulting dirty cleaning slurry was quickly soaked up using a wet vacuum and after rinsing with water With the floor clear I was able to spot stubborn areas that need more work and repeated the process.

With the stone clean I turned my attention to the grout lines and scrubbed in a strong dilution of Tile Doctor Pro-Clean which was then rinsed off with water. I then completed another spot check of the floor whilst using the wet vacuum to get the floor as dry as possible. With the cleaning part of the job complete I left for the day to allowing the floor to dry off fully overnight.

Sealing Sandstone Kitchen Tiles

Upon returning to the property the following day, I tested the floor with a damp meter, checking for any excess moisture that could prevent me from sealing the stone. The floor proved dry and so I began to seal the Sandstone starting with a single coats of Tile Doctor Colour Grow. Colour Grow is an impregnating sealer that is designed to fill the pores of the stone blocking dirt from becoming ingrained there whilst enhancing the natural colours in the stone at the same time.

Once the Colour Grow was dry I followed with the application of five coats of Tile Doctor Seal and Go which is a compatible water-based acrylic sealer which provides both a stain resistant surface seal and a durable low-sheen finish.


The floor now looks much healthier and the new sealer show keep it looking that way for some years to come.


Source: Sandstone Tile Cleaning and Sealing Service in East Cheshire

Renovating Old Victorian Hallway Tiles in Bedfordshire

A homeowner in the Leighton Buzzard was having some renovation work done to their property and during the course of the work discovered an original Victorian tiled floor underneath the hallway carpet. The town dates all the way back to the 12th century so period features like this are quite common.

Keen to have the floor restored the owner got in touch to ask if I could survey the floor and quote for restoring it, so my colleague Phillip popped round to see what needed to be done. Surprisingly the tiles were generally in quite good condition for their age with just a few cracks and chips here and there. There were some missing tiles that needed replacing but I was able to help them source replacements which were fitted before the cleaning work commenced.

Cleaning an Original Victorian Tiled Floor

I started the cleaning process by giving the tiles a deep machine clean with Pro-Clean which is a strong tile and grout cleaning product produced by Tile Doctor. A strong dilution was left to soak into the tiles before scrubbed in with a tile brush fitted to a rotary machine. This action lifted the surface soil and bits of plaster and paint which was then rinsed off and extracted using a wet vacuum.

With the soil and cleaning solution removed I then carried out a full inspection of the tiles in their natural state to see what other work would be required. As there was no apparent sealer present, I decided that the next step in the cleaning process would be to use a coarse 200 grit burnishing pad to clean and resurface the tiles, this was followed by a second rinse and wet vacuum. I then went around on hands and knees using Tile Doctor 100 grit diamond hand blocks to remove stubborn staining around the edges close to the newly painted skirting boards.

Sealing an Original Victorian Tiled Floor

The floor was allowed to fully dry for 2 days before I returned to apply Tile Doctor Colour Grow sealant which is an impregnating sealer that improves colour and is fully breathable, so it allows any damp from the sub floor to dissipate. Choosing a breathable sealer is important for these old floors which have no damp proof course and Colour Grow is normally my sealer of choice for Victorian floor tiles.

However Colour Grow dries to a matt finish and on this occasion the customer felt the finish still looked quite dull, although she was very happy with the results of the cleaning she asked if there was anything else I could do to brighten the finish, it was agreed that I would return a week later to carry out a damp test and if the results of this were favourable I would go ahead and apply several coats and apply Tile Doctor Seal & Go topical sealant which is water based and dries to a silk finish.

When I returned moisture, readings were taken which were acceptable, so as agreed I applied several coats of Seal and Go to give the tiles the desired appearance. With the work completed the customer was happy with the final results and even left the following feedback via the Tile Doctor feedback system.

Phillip arrived on time, worked very hard to prepare the floor- about 6 hours. Returned after floor was properly dry- 2 days. Applied a mat finish - 2-3 coats. I was disappointed with this finish, the floor which looked very flat and washed out. Each floor has its own characteristic and absorbs the products used differently. Phillip didn't disagree, so applied two coats of a glossy finish which has brought out the beautiful colours of my Victorian floor. All of this was done without a quibble. Happy with the finish now. My advice is to discuss fully the finish you require and get a patch test done before so everyone is clear about the job in hand. Would use again. Ms. A Binger , Leighton Buzzard





Source: Victorian Tile Cleaning and Restoration Service in Bedfordshire

Deep Cleaning a Small Travertine Tiled Hallway in Bedfordshire

Travertine floor tiles are very appealing but without the protection of a sealer they will soon suffer, fortunately this can be remedied as demonstrated in these pictures of a Tumbled Travertine floor at a house in the Village of Clophill in the Flit River Valley South of Bedford. This customer had called me out as her ten year old floor was looking very sorry for itself and she was concerned that a lot of holes were appearing which was making cleaning of the floor difficult as dirt was getting trapped in the holes. I went over and carried out a test clean on two separate tiles in the kitchen and the customer was amazed at how clean they came up and especially the grout. An appointment was made for the next month and work commenced.

Cleaning a stained Tumbled Travertine tiled floor

The first thing we do is to protect the lovely Oak kitchen units by removing plinths, covering base units and appliances with a protective film. We then commenced work by burnishing the stone with a set of Tile Doctor Diamond encrusted burnishing pads. The pads are applied individually to each tile in sequence starting with a coarse pad and finishing with the fine pad which brings up the polish. A little waster is used to lubricate the process along the way and the floor is rinsed in-between each pad with the resulting residue extracted from the floor using a wet vacuum. The process takes quite some time but the results are well worth the effort.


Once this was done our attention was turned to the grout which being recessed is difficult to reach by with pads. So for the grout a medium dilution of Tile Doctor Pro-Clean is applied to the grout lines and scrubbed in with stiff brushes by hand. The floor was rinsed again and fans were used to assist drying before filling the holes with the same filler the customer had used previously to match the colour of the stone as much as possible.

Sealing a Travertine tiled floor

When we returned the next day the floor had dried and we were able to give the floor a final polish with a very fine burnishing pad. The floor was then sealed with two coats of Tile Doctor Ultra Seal which provides excellent protection without changing the colour of the stone to provide a natural look.


My customer was delighted with the results and kindly left the following testimonial on the Tile Doctor Feedback system. "We had several rooms of very dirty travertine tiles that were deep cleaned, filled and re sealed. The floor now looks amazing. Fantastic job by a professional and friendly team.”



Source: Travertine Tile Cleaning and Renovation Service in Bedfordshire

Restoring Stained Victorian Hallway Tiles in Lancashire

This old Victorian tiled Hallway floor, laid in a geometric pattern, at a house in Barrow in Furness was a challenging project. The tiles were extremely dirty and also stained with Black Bitumen which has been used as an adhesive, however we have come across these sorts of problems before and so I was confident it could be resolved.

Deep Cleaning an Old Victorian Tiled Floor

I roped in Heidi and my son Lewis who spent a whole day cleaning with chemicals, steam, buffing pads and unfortunately the results were far from satisfactory; the customer wasn't happy and Heidi wasn't happy with it either. It was clear that the black bitumen had penetrated deep into the pores of the clay and becoming so embedded that no chemical or technique we were using would shift it fully.


To top it off I had gone out earlier to tile the old mat well with matching tiles before we started the cleaning but due to the depth of the floor matt. The matt well was at least 35mm so it was clear I couldn't use standard floor adhesive. I opted instead for a sand cement mix, similar to what the Victorians would have used originally. This filled up the depth and allowed me to tile and grout the same day, however overnight there was a bit of shrinkage and some of the new tiles settled unevenly.


I racked my head for a solution to both issues and decided the best course of action would be to Mill the clay tiles to remove the Bitumen and smooth down the uneven effect of my tiling. This is not something we would normally do on a clay tile as this system can leave scratches which potentially would look worse that the dirt. After I had milled the Tiles down with a course pad fitted to a heavy buffing machine and removed all the issues I then counteracted any scratches left over using a higher grit milling pad. This solution fully resolved both issues leaving it ready for the final step of sealing.

Sealing an Original Victorian Tiled Floor

The floor was left to dry off overnight and we returned the next day to seal the tiles using Tile Doctor Colour Grow, which is a matt finish, fully breathable and colour enhancing sealer which really lifts the colour of the stone or in this case clay tile. Colour Grow is impregnating – meaning that it penetrates the pores of the stone to fill them and prevent trapped dirt and stains. We recommend Colour Grow for both internal and external applications and especially for areas where no damp proof membrane is evident, since the sealer allows for the floor to breathe moisture.


There were plenty of problems to overcome and It took a lot of work but I’m pleased to say the floor was transformed by our efforts and now looks fantastic and I’m sure has added a lot of value to this period property.


Source: Victorian Floor Tile Cleaning and Renovation Service in Lancashire

Original Period Victorian Hallway Floor Restored in South Wales

Many property owners who are lucky enough to have an original Victorian tiled floor in their homes face the same conundrum: can an old and potentially very damaged floor be salvaged and restored to peak condition or should I replace it? Some people would instinctively tell you that the answer is no – even trained professionals! In fact, a leading tile restoration company (which shall remain unnamed) based in Cardiff told a recent customer of mine that her original Victorian tiled floor, dating back to 1905, was beyond repair. The company recommended that she not waste any money on having it restored and instead that she should have it ripped up and replaced.


It was in a bad state, however replacing the floor would incur a significant cost and the original characteristics of the period floor would be lost. The customer was feeling rather deflated and was left undecided on what to do. Fortunately after browsing the web for a solution, she came across Tile Doctor and I was asked to pop over and take a look. I visited the customer at her home and removed parts of her hallway carpet to get a better look at the Victorian tiles beneath. The floor was certainly in a very poor state, there were many old paint splash marks covering the tiles and the surface of the floor was deeply darkened after many years’ worth of wear and tear. In my opinion however, it was still salvageable, and the customer was happy to see what could be done.

Cleaning an Original Victorian Tiled Floor

A week before I was due to start the restoration, I asked the customer to remove the foam-backed carpet to let the floor breathe a bit. Before beginning the work, I ran a few damp tests and the floor proved surprisingly dry considering how old it is and the very probable lack of a damp proof membrane. I started by manually scraping as much of the old paint staining off the stone as possible and cleared other debris from the surface. Knowing that clay based Victorian tiles like these easily soak up paint splashes, I knew it would take a thorough clean to remove them completely. I firstly soaked the floor with water and left it to dry slightly before mixing a concoction of Tile Doctor NanoTech HBU, Tile Doctor Pro-Clean, and Tile Doctor Remove and Go. NanoTech HBU is a particularly powerful cleaner which uses nano-sized particles to penetrate the pores of the stone, while Pro-Clean is an alkaline-based cleaner that tackles heavy soil build-up. Remove and Go is a multi-purpose product which both cleans and strips away any old sealer. I left this mixture to dwell on the floor for around half an hour, scrubbed it in firstly using a black scrubbing pad fitted to a rotary machine and then a wire wool pad. I followed by rinsing the products off with water and extracted up the excess with a wet vacuum machine. This technique was repeated until I was satisfied with the condition of the floor.

Sealing an Original Victorian Tiled Floor

After leaving the floor to dry off completely overnight, I returned to the property the next day to carry out the sealing process. I applied seven coats of Tile Doctor Seal and Go, which not only adds a protective covering to the tile, but also enhances its appearance. The customer was absolutely thrilled with the results of the restoration, especially considering that she was told the floor was ruined by a leading company and not worth saving.




Source: Victorian Tile Cleaning and Restoration Service in South Wales

Sealing Porcelain Tiles in Surrey

Photographs below from a lovely house in Windlesham where I was asked to do something about the Porcelain floor tiles which had become extremely dirty and were proving impossible to clean. Infact my customer was pulling her hair out about how to fix this issue of deeply ingrained muck and was on the verge of pulling the whole lot up.

Porcelain Tile Cleaning

Normally Porcelain tiles are fairly easy to maintain and it’s just a question of keeping the grout clean however I have to confess these tiles were perplexing indeed. In fact to be honest...I tried every product in my van to get them clean, finally settling on Oxy Gel. I left it to soak on the floor for 30 minutes and then worked it in with an aggressive 200 grit pad. I’m happy to report the transformation was amazing, all the muck was released from the tile and I was able to extract it from the floor using a wet vacuum. My last step was to give the grout a good scrub using more Oxy Gel, rinse off with water and extract as much moisture as possible with the wet vacuum.

Porcelain Tile Sealing

I speed dried the floor with an air mover and once the floor was dry I applied a coating of Tile Doctor Ultra Seal. Now Porcelain tiles don't usually take a sealer however these tiles were unusual in that they were trapping dirt and it’s possible they were in fact micro-porcelain so a coat of sealer was added for good measure.


My customer was really pleased with the difference and left the following comment on the Tile Doctor feedback system:

“Here's what she said-
"Rupert was a total professional from start to finish. I was worried as to how good he would be able to make the floor - the floor consists of almost white porcelain tiles, that my tiler had failed to seal. This meant they had absorbed dirt over the last two years - even after me scrubbing the floor, they always looked dirty. The room was big - a 24 feet long kitchen/dining room. But Rupert assured me he could get it clean again - and he was as good as his word. When I saw the room for the first time, I said "I have my new kitchen back - the floor looks as good as it did the day the tiler had put the tiles down". He left everything clean and tidy after the job - I wish I had discovered your website 18 months ago ! Thank you, Rupert, brilliant work."”


Source: Porcelain Cleaning and Sealing Service in Surrey

Removing Coatings and Sealers from Stone

Slightly different story for you below; this time from the medieval town of Tewksbury which dates all the way back to the 8th century. A customer there had asked if there was anything that could be done to restore the appearance of their polished Limestone kitchen floor on which he had previously applied a wood sealer which had turned the tiles brown. I inspected the floor and ran a test clean on a small section of tile which successfully removed the wood seal. This gave the customer the confidence to book me into to complete the job which I estimated would take three days to strip off the old sealer, deep clean and reseal with a more appropriate product.


You probably can’t appreciate how bad the tiles looked from the photograph above but if you look at the indicated area under the kitchen units where the kick boards have been removed you can really see how the brown stain in the wood sealer has darkened the look of the tile.

Removing Old Sealers from Limestone Kitchen Floor

On the first day I prepared the area by removing the kick boards from the underneath the kitchen units so they wouldn't get affected by the cleaning process and started wetting the floor with water. The water lubricates the burnishing process whereby coarse diamond encrusted pads are applied to the floor with a buffing machine. We started the process using a very coarse 100 grit milling pad to remove the wood sealer before moving onto the finer pads from 200 grit, 400 grit, 800 grit and finally 1500 grit pad building the finish of the floor as we progressed. The floor is rinsed with water between pads and the slurry is removed using a wet vacuum. This burnishing process took up all of the first day so the next day I returned to focus on the edges I had missed and the grout lines, being a relatively small format tile for Limestone there was a lot of grout to cover. I tacked the grout lines with Remove and Go which is a powerful stripper and cleaning agent which is applied along the grout line and then scrubbed in with a narrow stiff brush before being rinsed away with water. The edges were treated with a set of small six inch milling pads fitted to a hand held buffing machine in a similar process as on the first day.

Sealing a Limestone Tiled Floor

On the third and final day the floor was spray burnished which a process is involving a very fine 3,000 grit floor burnishing pad and a little water spayed onto the floor during the application. This process really tightens up the pores in the stone and restores its appearance. After making sure the floor was free of any lose grit I then proceeded to seal the Limestone with Tile Doctor Ultra Seal which is a natural look sealer that doesn’t alter the appearance of the stone but penetrates into the pores of the stone to protect it from within. I left it to dry for an hour then buffed the floor with a white buffing pad before apply a second coat. This was also left to dry for an hour before running the buffing pad over for a last time.


It took a fair amount of work to get the floor looking back the way it was meant to be but I’m very pleased with the outcome and more importantly my customer was really happy.




Source: Limestone Cleaning and Sealing Service in Gloucestershire

Grout Cleaning and Sealing in a Warwickshire Hallway

The owner of this house in Chaplefields near Coventry had bought this property as an investment and was keen to improve its appearance. As part of this work he had lifted the vinyl tiles in the hallway and discovered a lovely Edwardian tiled floor. Unfortunately, whoever had laid the Vinyl tiles had decided to use Tar as an adhesive and this had left a black mess all over the floor.


Realising the potential value an original feature such as this could add to the property he was keen to restore the tiles but not so keen to deal with the Tar, so we were asked to deal with the problem and restore the floor as close to its original condition as possible.

Repairing and Cleaning a Dirty Edwardian Tiled Floor

To get the tiles clean and remove the horrible tar I applied a strong dilution of Tile Doctor Remove and Go, which as its name suggest is great for removing coverings from tiles. I applied the Remove and Go with a mop, left it to soak in for a few minutes and then worked it in using a rotary machine fitted with a black scrubbing pad. The soil was extracted off the floor using a wet and dry vacuum and then the process repeated until I was happy all the tar was gone. I then gave the tiles an acid wash using Tile Doctor Acid Gel; this serves to break down alkaline mineral deposits such as cement and grout smears, it also counters any efflorescence problems which can be an issue with these old floors where no damp proof membrane has been installed. Finally, the floor was given a rinse with clean water and a steam clean to remove any trace of cleaning products and to neutralise the tiles in preparation for sealing.

Sealing a Edwardian Tiled Floor

I left the floor to dry off overnight and returned to the property to seal the tiles the next day. To seal the tiles, I used three coats of Tile Doctor Seal and Go which is a water based sealer that leaves a subtle sheen finish and being water based doesn’t leave a smell as it dries. The sealer will provide durable protection going forward preventing dirt from becoming ingrained into the pores of the tile and ensuring it remains easy to clean and keeping its appearance for some time to come.


The floor now looks fantastic and gives a great impression when you come into the property which is exactly what the owner wanted.


Source: Edwardian Tile Cleaning and Restoration Service in Warwickshire

Putting the shine back on a Slate floor in Gloucester

This Slate tiled floor in the hallway of a property in Gloucester had been laid 28 years ago, but during this time had received no proper maintenance. The property owner used to clean the tiles once a week using a steam cleaner to little effect.


In fact, we don’t normally recommend steam cleaning sealed surfaces as it will erode the sealer prematurely. After countless years of steam cleaning, I was confident that any traces of old sealer on this floor would be non-existent at this point. This is, of course, a problem because a lack of sealer exposes the stone to ingrained dirt and stains. The effects of this are shown in the photos below: as you can see, the Slate had completely lost its lustre and naturally colourful patina.


I was asked by the property owner to provide this Slate tiled hallway with the restoration that was so long overdue, so I travelled to the house in Gloucester, a city situated near the Welsh border and between the Cotswolds and the Forest of Dean.

Cleaning a Dirty Slate Tiled Hallway

I started the restoration by mixing a strong solution of Tile Doctor Remove and Go combined with Tile Doctor NanoTech HBU. These two products serve different purposes. Remove and Go is a stripper designed to break down any traces of old sealer that might still have existed, as well as any paints and adhesive markings; NanoTech HBU is a potent cleaner which contains nano-sized cleaning particles that penetrate deep into the stone to get underneath tough dirt and stains to dissolve and lift them out. This cleaning solution was spread over the floor and left to dwell for 30 minutes, before being scrubbed in using a black scrubbing pad fitted to a buffing machine. A thick black slurry resulted from this process and this needed to be removed using a wet vacuum.


Next, I repeated this cleaning process using Tile Doctor Pro Clean, our reliable alkaline cleaner, to provide a more thorough clean for the tiles and grout. The slurry was once again removed using a wet vacuum, before I then rinsed the whole floor with fresh water to remove any traces of chemicals. When satisfied with outcome of the cleaning process, I left the floor to dry overnight.

Sealing a Slate Tiled Hallway

Upon arriving back at the property, the next day, I ran some quick moisture tests to check that the floor was dry. Thankfully, there were no damp issues and I was able to seal the tiles using four coats of Tile Doctor Seal and Go, leaving each coat to dry before applying the next. Seal and Go is a water based sealer (so no smell as it dries) which adds durable stain resistance and a low-sheen finish that brings out the best in the slate.


The customer’s reaction to the outcome of the restoration was fantastic. She never expected the floor to turn out so beautifully and was very pleased.




Source: Slate Tile Cleaning and Sealing Service in Gloucester

Restoring an old Quarry Tiled Farmhouse Kitchen Floor

Rackenford is a tiny village in North Devon, with a population of approximately 400 people, and is surrounded by many farms as agriculture is the main source of employment in the area.

I recently visited one of the farmhouses in the area at the request of the property owner who needed help restoring an area of Victorian quarry tiles which were around one hundred and twenty years old. The floor had been extended with a new batch of tiles which ran into a later extension about ten years prior. Both areas were dirty and attracting grime and the older tiles had some heavy damage to some tiles and had lost the colour which was indicative of being covered by carpet for a long period and salts had dried in to the tiles, damaging them and creating an orange peel type of surface.

In the past, the floor had been sealed with a topical sealer i.e. one that sits on top of the tile rather than being absorbed into it. In most areas, the sealer had long since worn off but in a few areas that it remained it had been scratched by the chairs near the large inglenook fire at one end of the room.

The customer was looking to clean and re-seal the whole floor to try to improve the look of the damaged tiles but also to make the floor easier to keep clean and maintain and were hoping that the divide between old and new tiles was less striking.

Cleaning a Dirty Quarry Tiled Kitchen Floor

When it comes to cleaning natural stone tiles, our go-to cleaning product is Tile Doctor Pro Clean. Pro Clean is a multi-purpose, high alkaline cleaner that serves to both strip away any old and ineffectual sealer, and clean heavily soiled stone. The product is suitable for use on all types of natural stone and tiled floors.

I mixed a strong dilution of Pro Clean and water before spreading it liberally across the whole floor. I then left it to dwell for roughly 10 minutes before proceeding to agitate it with a scrubbing brush fitted to a heavy rotary machine. This helped to eradicate the soil build-up. Any resulting cleaning slurry was promptly removed using a wet vacuum, before the floor was left to dry completely overnight.

Sealing a Quarry Tiled Kitchen Floor

Returning to the property the next day, I immediately ran some damp tests to see if there was any excess moisture present on the floor. Knowing that this was an old property, I expected that there would be no damp proof membrane installed and this would increase the chances of damp issues.

Thankfully, the floor proved to be completely dry and I was able to seal the floor using eight coats of Tile Doctor Seal and Go. Seal and Go is a water-based acrylic polymer sealer that provides both a stain resistant surface seal and a durable, aesthetically pleasing low-sheen finish that helped to return the natural reddish colours to the Quarry tiles. Although the top layer of the damaged tiles had been lost the colour had returned and were now looking much healthier.

With a fresh seal in place, the floor will now be much easier to clean and maintain. The customer was really pleased with the outcome of the restoration, which you can see in the photos below. Another satisfied customer!


Although nothing can really replicate a hundred years of patina, the difference between the old and new tiles was reduced with a good clean and a consistent finish throughout. Certainly, the customer was happy and left the following feedback:

"We are very pleased with this refurbishment of old quarry tiles, which have regained colour and texture. The overall slight gloss added to both these and the newer tiles next to them makes a huge difference to the whole picture. The cleaning and maintenance guide is also very useful. The bill was also very reasonable for two intensive days work - many thanks"




Source: Quarry Tile Cleaning and Restoration in Devon

Terrazzo Tiled Hallway Polished in South Wales

Terrazzo is a quite a bit different from the natural stone floors we most commonly work with. It's a type of flooring material that was made popular by Venetian builders in Italy in the 1920s, but is ultimately descended from styles of design that date back hundreds of years. A typical Terrazzo floor consists of chips of marble or granite set in concrete and polished to result in a smooth surface. This Terrazzo floor, installed in the hallway of a property in Bridgend, South Wales, was in Read more...

Dirty Terrazzo Floor Deep Cleaned, Burnished and Sealed in Bridgend

Terrazzo is a quite a bit different from the natural stone floors we most commonly work with. It's a type of flooring material that was made popular by Venetian builders in Italy in the 1920s, but is ultimately descended from styles of design that date back hundreds of years. A typical Terrazzo floor consists of chips of marble or granite set in concrete and polished to result in a smooth surface. This Terrazzo floor, installed in the hallway of a property in Bridgend, South Wales, was in Read more...

To read more on this topic click here

Removing Vinyl Glue From Terrazzo Tiles

Terrazzo is a quite a bit different from the natural stone floors we most commonly work with. It’s a type of flooring material that was made popular by Venetian builders in Italy in the 1920s, but is ultimately descended from styles of design that date back hundreds of years. A typical Terrazzo floor consists of chips of marble or granite set in concrete and polished to result in a smooth surface. This Terrazzo floor, installed in the hallway of a property in Bridgend, South Wales, was in relatively good physical condition, but it had clearly lost its shine due to the build-up of dirt and muck over the years. In fact, it was first installed in around 1940! The owner was keen to have it rejuvenated to its best possible condition, so they asked me to come in to see what I could do.

Cleaning and Burnishing a Dirty Terrazzo Tiled Floor

My first course of action was to apply Tile Doctor Pro Clean liberally across the floor and leave it to dwell for a short period. This is a high alkaline cleaner that is designed to deal with light to moderate soil build-up, and to strip away any old sealer remaining on the floor. I scrubbed the product in using a black pad fitted to a rotary machine and vacuumed up the resulting cleaning with a wet-vac machine. Next, to restore the shine to the floor, I undertook a process known as burnishing, which involves the application of diamond encrusted polishing pads. We will typically start with a Coarse grit pad to level off any uneven areas of the floor and grind down any particularly stubborn marks and stains. Then, we gradually refine the polish on the floor using Medium and Fine grit pads. A small amount of water is used as lubrication with each pad. After I had finished applying the first three pads in our four-pad system, I gave the floor a thorough rinse and left it to dry overnight.

Sealing a Terrazzo Tiled Floor

I returned to the property the next day and immediately ran some damp tests to check for excess moisture issues, which one might expect with an old floor like this one. Thankfully, the floor proved dry – and I could finish the burnishing process with the fourth and final Very Fine diamond encrusted burnishing pad, which achieved a beautiful shine finish. Finally, I sealed the floor with three coats of Tile Doctor Colour Grow, an impregnating sealer which provides robust protection and enhances the coloured patterns in the Terrazzo.


As you can see from the photos above, the floor is looking so much more colourful and bright after a deep clean, polish and a fresh seal. The customer was over the moon!


Source: Terrazzo Tile Cleaning and Restoration in South Wales

Quarry Tiled Floor Restored in Shop to Flat Conversion in Oxford

This ground floor flat in the City of Oxford had been converted from a shop which as you can imagine, was quite complex. One significant element involved in the conversation was the restoration of an old Quarry tiled floor which ran through the main hallway and had for many years been covered in Read more...

Heavily Stained Quarry Tiled Floors Restored in Oxford Shop Conversion

This ground floor flat in the City of Oxford had been converted from a shop which as you can imagine, was quite complex. One significant element involved in the conversation was the restoration of an old Quarry tiled floor which ran through the main hallway and had for many years been covered in a commercial linoleum covering. When the linoleum covering was removed, the sheer amount of glue which had been used to affix it had completely ruined the appearance and condition of the Quarry Read more...

Rejuvenating Salvaged Flagstone Tiles at a Property in Ledbury

Here we have an interesting situation in which an old Flagstone tiled floor had been salvaged from a cottage approximately 30 years ago and subsequently reinstalled at a house in Ledbury, a small market town which lies to the west of the Malvern hills in the North of Gloucestershire. Since being reinstalled, the Flagstone tiles had been barely touched in terms of maintenance for three decades and so the stone and grout were naturally in need of a deep clean and seal! The property owner had Read more...

Restoring Salvaged Flagstone Flooring in a Gloucestershire Kitchen

Here we have an interesting situation in which an old Flagstone tiled floor had been salvaged from a cottage approximately 30 years ago and subsequently reinstalled at a house in Ledbury, a small market town which lies to the west of the Malvern hills in the North of Gloucestershire. Since being reinstalled, the Flagstone tiles had been barely touched in terms of maintenance for three decades and so the stone and grout were naturally in need of a deep clean and seal! The property owner had Read more...

Amtico Kitchen Floor Cleaned and Sealed in Lancashire

Photographs below from the maintenance of Amtico Vinyl Floor Tiles in the kitchen of a house in the village of Heysham which is famous for its ferry port that has links to the Isle of Man and Ireland. This Vinyl wasn't that dirty but it was starting to lose its sheen and when this happens it's Read more...