Installing Granite Flooring Tiles

Granite flooring tiles definitely add attitude to any space. It is for this reason that a lot of people want to have this type of flooring option in their homes. Granite is, in fact, known for its sturdiness and beauty. If you are planning to install granite flooring tiles, here are the steps you should follow:
Granite flooring tiles

What You'll Need:

• Sander
• Plastic spacers
• Backerboard
• Backerboard screws
• Wet saw
• Thinset
• Rubber mallet
• Notched trowel
• Grout sponge
• Grout float
• Grout sealer
• Paper towels

Step 1 – Clean the Area

The area that you would be working on must be completely dried and cleaned. Sand off any peeling paint or sealant that is still on the area. Make sure to clear floor imperfections with waterproof products.

Step 2 – Lay Granite Flooring Tiles

Get to the an area with a 90-degree corner and lay out your granite flooring tiles. Plastic scrapers can be used to hold the granite flooring tiles in their places. Trim the tiles according to your need. Laying the granite flooring tiles beforehand would let you assess if you need more materials.

Step 3 – Create the Thinset

Read the package directions for mixing the thinset. Once this is mixed, get the trowel to apply a thin but even thinset layer on the subfloor. Get the backerboard in place by screwing down a backerboard screw. Do this carefully so you can be assured that your granite flooring tiles are protected from damages.

Step 4 – Press the Tiles on the Thinset

Create ridges while spreading the thinset that you’ve mixed by angling the trowel to a 45-degree position. Remember to lay out the thinset in areas that you can cover tiles within 10 to 15 minutes. Otherwise, the mixture will harden without the tiles on it. Lightly twist each granite flooring tile into the thinset. Use the rubber mallet to lightly hammer down the tile. This process would ensure that no airpocket is under the granite flooring tile. Carefully follow this step until all of your granite flooring tiles are installed. Stay off the tiles for at least 24 hours.

Step 5 – Apply Grout

Mix small batches of grout to a consistency similar of a toothpaste. Make sure that you only mix batches that are good enough for 20 minutes of application. Set your mixture aside for 5 minutes. After that, apply grout to the joints of each tile by using a grout float. Use a damp sponge to clean off any kind of grout excesses. Leave it to dry for approximately 72 hours.

Step 6 – Apply Grout Sealant

Once the grout on the tiles has completely dried, use a penetrating grout sealant to ensure that no moisture or water can get through your granite flooring tiles. Ready your paper towels to remove grout sealant excesses. Do this immediately as the sealant would easily dry out and mar the surface of your granite flooring tiles. Let the sealant dry for approximately 24 hours.

Source: www.DoItYourself.com

Deep Cleaning a Victorian Tiled Hallway in Devon

I was contacted by the owners of an old Farmhouse in the East Devon village of Broadclyst to look at their Victorian Tiled Hallway floor which as you can see from the photograph below was heavily stained and had also been splashed with paint from decorating. Victorian tiles are very robust and can take a lot of punishment which you certainly get in a farmhouse, however once the sealer wears off dirt gets into the pores of the tile making it very difficult to clean.

I visited the property to take a closer look and to take some moisture readings because these old floors don’t have a Damp Proof Course and moisture levels too high can restrict when this type of work can be done due to the sealers needing the floor to be dry in order to cure. I also did a test piece to show the customers what level of cleaning could be achieved.

Cleaning a Victorian Tiled Hallway

With the customers happy with the quote I returned to complete the work starting by covered the skirting and bottom of the stairs to protect the paintwork and carpet. I then put a strong stripper/degreaser called Pro Clean on to the floor, ensuring even coverage and keeping and eye on the floor to make sure that it didn’t dry out.

After a short dwell time I set to work scrubbing the floor with a 400 grit diamond burnishing pad and using small hand blocks to get into the corners and any edges not reached by my machine. Once I was satisfied that the tiles were as good as they could be I rinsed the floor to remove the alkaline cleaner and soiled water.

This was followed by giving the floor an Acid rinse using Tile Doctor’s Acid Gel, this process counteracts any alkaline salts that can rise up through the tile as it dries out, a process which is more commonly known as efflorescence. This can be quite a problem on floors like this that don’t have a damp proof course (floors generally didn’t pre-1950s). I had to be careful not to leave the acid down for too long because these tiles are susceptible to acid damage.

Dealing with salt issues on these old floors (efflorescence) is essential because they can damage the sealer or become trapped under it, detracting from the beauty of the floor. Given the age of the farmhouse it’s difficult to know what the floor had been laid onto. Often it was compacted rubble and building works from the erection of the adjoining buildings; additionally some of the later Victorian floors were laid on a wet limecrete scree which contain a high salt-content.

Before I left for the day I left an air mover on the floor to aid in the drying of the tiles. If there are radiators in the area I also suggest that they are turned on overnight to further aid the drying process. Occasionally these types of floors need to be left for several days to dry but it is worth the wait and the floors can be used in the meantime provided indoor shoes and socks only are used and care is taken not to get the floor dirty.

Sealing an Old Victorian Tiled Hallway

Upon returning the next day I tested the moisture content of the floor and was pleased to find that it was well within acceptable levels for the application of the sealer that I was planning to use. I quickly checked the floor for areas that I felt may be able to be improved and once satisfied a single coat of matt-finish, colour-enhancing sealer called Colour Grow was applied before two coats of a Seal and Go sealer was used to give the floor a satin finish, which I think gives it a slight glaze and freshly mopped appearance.


The customers were thrilled and said that they wished they had brought me in sooner!


Source: Victorian Tile Cleaning and Sealing Service in Broadclyst, Devon

Pros and Cons of Floor Heating Mats

When winter rolls around and your floors turn stone cold, use floor heating mats to take the chill out of going barefoot. Not only will you see heating bills reduced, but you will also get rid of dust and particles that traditional forced air systems spread around the house. There are many pros to electric floor heating mats. Floor mats work like a big electric blanket underfoot.

Pros

• Energy efficient
• Adds additional insulation
• Noise-free
• Reduces allergens
• Easy installation
• Safe
• Invisible

Cons

• Installation can be pricey
• Sometimes cannot be retrofitted

In the past, it was difficult to install radiant flooring under existing wood or carpet. Usually, heated floor mats were added during construction. Older models often required cement to be installed with the electrical system, but not today. Most floor heating mats on the market are easily installed directly underneath carpet and floating wood.

Note, however, that certain types of tiled flooring will have to be replaced if you want to install heated floor mats. If you are doing a remodel, it would be the perfect time to add radiant flooring under your tile. For the rest of your house, installation should be quick and easy.

Source: www.DoItYourself.com

Renovating a Small Victorian Tiled Entrance in Edinburgh

If you visit Victorian era houses throughout the UK, you will find that many them have colourful tiled entranceways (also sometimes known as vestibules). The tiles are commonly made from encaustic cement, stylised with distinct geometric patterns that really help to add character to the property.

The reign of Queen Victoria was a prosperous and confident time for Scotland – and many new houses and buildings were built in the well-known ‘Victorian’ style during the period. One of the best-known buildings to be built was Balmoral Castle, which is still in use by the Royal Family as a holiday home.

Homeowners who are fortunate enough to be in possession of original Victorian tiles will find that they are not easy to keep clean without the right products and methods. The entrance to any house of course is subject to high amounts of foot traffic, which means the tiles can become dirt and discoloured very quickly indeed.

Here is an example that we cleaned and sealed recently in Edinburgh, although in good physical condition for its age the sealer on the floor had worn off and dirt had become ingrained in the tile reducing its overall appearance.

Cleaning Dirty and Discoloured Victorian Tiles

Having restored hundreds of Victorian tiled floors in the past, Tile Doctor has developed tried and tested methods for cleaning all types of tiled floors so tackling this small floor would not be a problem.

To begin, we gave the floor a deep clean to break down any old sealants and to cut through thick layers of dirt and grime. The cleaning solution we employed consisted of two products: Tile Doctor Pro Clean (which is a strong alkaline cleaner) and Tile Doctor Remove and Go (which is a stripping agent formulated for the removal of old sealants, synthetic coatings, glues, and paints). The solution is applied and left to soak into the tile for ten to twenty minutes before being scrubbed in, which for a small area such as this needs to be done by hand. The soiled solution is then rinsed off with water and this is then extracted using a wet vacuum. This deep cleaning process was repeated several times to make sure the tiles were as clean as possible.

Once we were happy that all the dirt and grime had been removed, we gave the floor a quick acid wash using Tile Doctor Grout Clean-Up to remove any old grout smears and to neutralise any potential salt efflorescence issues. The floor was then given a final rinse before leaving it to dry off fully overnight and a turbo air mover was left running to help speed up the process and ensure the floor was completely dry to be sealed the following day.

We are very conscious of the fact that many of these old Victorian tiled floors to have damp-proof membranes installed beneath them, so we wanted to guarantee there would be no damp issues that would prevent us from applying a fresh sealant. This is because even a small amount of excess moisture can potentially damage the performance of the sealant.

Sealing an Original Victorian Tiled Entrance

Returning to the property on the second day, we proceed to seal the tiles with three coats of Tile Doctor Colour Grow. This sealant soaks into the pores of the tile protecting it from within and providing long term protection, it also enhances the colours in the tile in the process.

The difference made by this two-day restoration is shown below. It is quite amazing how quickly these results can be achieved considering the age and previous condition of the tiles. Our customer was absolutely thrilled.




Source: Victorian Tile Cleaning and Sealing Service in Edinburgh

Refinishing Granite Flooring

Any kind or color of granite flooring provides a lively appeal to rooms and spaces. However, like all good things, the beauty of these items might fade over time. The luster of granite flooring may diminish thus making your floor look old and unattractive. Good thing there are steps that you can follow to make sure that your granite flooring always look as good as new. These steps include refinishing. This type of granite flooring maintenance is usually performed by equipped workers. However, those who believe that they can perform the job well, follow the steps below.

What You'll Need:

• Industrial sander
• Diamond pads with abrasive grits
• Diamond pads with less abrasive grits
• Buffing chemical solution
• Clean rug
• Broom
• Pail of water

Step 1 – Clean the Granite Flooring Area

Granite flooring undoubtedly loses its luster and shine because of dirt and stains. Make sure that your granite flooring really needs refinishing by removing dust particles and stains using a broom, clean rag and water. Consider letting it dry after cleaning to see if you need to proceed to the next steps.

Step 2 – Flatten Your Granite Flooring

Once you have determined that your granite flooring really needs refinishing, start the steps to flatten out the tiles. Get a regular industrial sander to even out slants and rough edges on your granite flooring. Flatten areas that have seemingly irremovable stains. Clean off dusts and debris.

Step 3 – Hone Your Granite Flooring

Fit a diamond pad with an abrasive grit to your industrial sander. Get to the spots that have deep scratches, slants and rough surfaces. You can also use the diamond pad-powered industrial sander to get rid of the hardest to remove stains and similar impurities. Be careful not to hone the areas that do not need further sanding as this would only create irregular textures.

Step 4 – Polish Your Granite Flooring

Remove the diamond pad with abrasive grit from your industrial sander and replace it with one that has a lot less abrasive grit. Again, run your industrial sander on the entire space of your granite flooring. Remember to do this with care so as not to damage your precious granite tiles. Clean off dust with an airbrush to determine if you still need to do the next step. If you think that your granite flooring has gained back its shine and luster, stop your refinishing routine here.

Step 5 – Buff Your Granite Flooring

Buffing for granite flooring only takes place when the project involved is considered to be old. Those who have abandoned spaces usually resort to this last step to gain back the shine of granite flooring. Get a buffing chemical solution especially made for granite floor. Apply it to the area concerned as instructed by the packaging. Leave the chemical solution to dry unless otherwise advised. The solution would begin a chemical reaction that would bring out the best shine possible from your granite flooring. Read the instructions of the solution as you might need to use a floor polisher for the best results.

Source: www.DoItYourself.com

Renovating Victorian Tiled Hallway Oxford

The Victorian tiled hallway shown below had until recently been covered by carpet and was in surprisingly good condition for its age which is a testament to the durability of these floors. My client who lives in Oxford had managed to remove most of the glue that had been used to secure the carpet to the tile but found it had left an imprint on the floor. Unable to take the restoration any further we were asked to remove the ground in grime and seal the floor.

Restoring Victorian Quarry Tiles

My first task was to remove what was left of the carpet adhesive primarily with the aid of scraper which was used carefully along the edges. This removed the thicker parts of the glue but needed more work to remove all the traces; so a 50 grit disc fitted to a handheld machine was run around the edges of the whole floor to complete the job removing the residue and dirt in the process. I then used a 50 grit milling pad attached to a rotary floor machine to remove the ground in grime and clean the whole floor. The floor was then rinsed with water to remove the soil that was generated afterwards and then the process repeated this with a 100 grit and 200 grit milling pad to fully restore the appearance of the tile. This process took up most of the day so before leaving I gave the floor an acid wash using a mild dilution of Tile Doctor Grout Clean-up and then followed this with a good rinse and final clean with Tile Doctor Neutral Cleaner.

Sealing Victorian Tiles

Having finished cleaning the floor I left it to dry off completely for three days to ensure it was bone dry before returning to seal it. To seal I applied Tile Doctor Colour Grow which is an impregnating sealer that protects the tile from within by occupying the pores in the clay, it also enhances the natural colours in the tile in the process and leaves a matt finish.


The finished floor looks a lot brighter now it’s now free of all the dirt and glue marks, the new sealer will also ensure it’s easy to clean and keeps its appearance for some time to come.



Source: Victorian Tile Cleaning and Renovation Service in Oxfordshire

Building a Floating Floor on an Uneven Surface

A floating floor can really spice up any kind of home design. Some even serve multi-purposes such as a small stage for live performances and the likes. However the floor will be used, it is necessary that the area where the floating floor would be installed first be inspected.

Ideal Locations for Floating Floors

Ideally, a floating floor must be installed in a sturdy and even space. If this is not the case in your set-up, you should search for ways to improve the location of your floating floor.

Preparations in Correcting Uneven Surfaces for Floating Floor

Decide on the space where you would be putting up your floating floor. If you are considering using wood, make sure that the area you would choose would be safe for such materials. As such, laying a wooden floating floor on soil would need more considerations to ensure the protection of the wood.

Measure the area to ascertain what materials you would be using. If you are laying floating floor on the ground, considering having dips filled up with soil. You could also have rising areas plowed prior to the installation of your floating floor.

Sanding and Filling

For concrete and other similar subfloors or grounds, it might be best to allot a budget for sanding and filling. Get a level to determine the areas which you need to level. Evenly sand those areas that are a lot higher than the rest of the surface. Dust off all debris before measuring it up using your level. For dips, get concrete putty or other similar filler. Apply this to areas that need fillings. Let it dry completely before measuring it again. Sand the fills that has risen to more than the desire level.

Installing a floating floor on an uneven surface could also be achieved by skipping all the above-mentioned steps. However, the task at hand would be trickier. Thoroughly clean the area where you would be building the floating floor. After that, measure the areas where there are depressions and rises. The “legs” of your floating floor should be made to fit such sections.

In this regard, you need to measure up each of the fills and rise to be able to adjust the sizes of your floating floor’s legs. Measuring and wood cutting are the most important steps here. Any miscalculation could lead you to the misfit of the floating floor’s legs to the surface. Also, remember that the materials you would be using for the floating floor’s legs should be the sturdiest. These parts are like foundations that would be tasked to carry most of the pressure to the floating floor.

After all the adjustments have been done, continue on attaching the floor boards of your floating floor. Drive down nails and screws next to each other to stop the boards from squeaking. Also, double check for surface impurities that would need sanding. Hammer down each nail to ensure that they don’t come loose. Apply varnish and paint as desired.

Source: www.DoItYourself.com